Kenmore 16238 Instrukcja Użytkownika

Assembly and OperationKen moreLiquid Propane Gas GrilTHIS GRILL IS FOR OUTDOOR USE ONLYCAUTIONARead and follow all Safety Statements, Assembly instruc

Get it fixed, at your home or ours!Your HomeFor repair-in your home -of all major brand appliances, lawn and garden equipment, or heating and cooling

10. Position console/valve assembly over tabs as shown.Locate Console on tabs as shown. (Right side shown)Note: Check wires from switch harness

11. Assemble shelf support brackets by sliding shelf bracket (A) and Shelf bracket (B) together while paying close attention to hole alignment, and at

14. Position ieft side shelf over shelf mounting brackets15. To begin installation be sure to align iarge shelf (holes) with the small holes in the sh

18. Attach side burner lid handle, side burner lid and burner tray.19. First begin by attaching side burner lid handle to side burner iid using (2)

Front View Front View22. Attach side burner assemblies using shelf mounting procedures as previously described. (Steps 14 & 15)23. After attachi

Attach side burner valve and bezel using (2) #8 x 3/8 tapping screws as shown.Insert side burner knob.TappingScrews25. Position base casting down over

26, Position bottom cross lighter assembly as shown, being sure to feed ignitor wires through the front holes in the bottom of the base casting. Botto

27. Install burners by feeding burner though slot in the base casting and guiding burner tube over orificein valve, see illustration below. Secure bur

28, Install three cross lighter spacers over threaded studs in bottom cross lighter, then install cross lighter top plate.IMPORTANTTabs in cross light

Table of ContentsLimited WarrantyWarranty,,... 2Safety...

29. Install Heat Distribution Plate by placing in position so that the six supports rest on the six ribs in the base casting.20

30. Install Lid, Overlay, Handle, Cooking Grid, Warming Rack, Hinge Clip, and Logo. Install lid before installing overlay, logo, and temperature gauge

31. Install grease tray from rear of grill by sliding grease tray in on support rails until the front of the tray drops down over the front of the sup

32. Attach the two wires from the cross lighter and the two wires from the side burner to any of the four small terminals on ignitor module as shown.N

35. Place tank into hole located in bottom plate.Insert Tank Bracket into Slot and rotate it 90 Degrees. Slide bracket down over tank ring to hold ta

OPERATIONWarning: Before proceeding with the following steps, ensure you have read the L.P. Gas Cylinder hose and Regulator sections of this Assembly

BREAKING IN YOUR GRILLBefore cooking on your gas grill for the first time, you should "break it in" by operating it for a short period of ti

CLEANING & MAINTENANCETo keep your grill working at its peak efficiency as well as contribute to the safe operation of this unit, perform all of t

It is possible that very small insects could make webs or nest in the venturi tubes. This ii# will partially or completely block the flow of g gas thr

Part ListKenmore Propane Gas GrillREF# PART#QTY DESCRIPTION1.SP5051-261Logo2,SM5006-1L 1Lid3.SP5002-30 1Temperature Gauge4,SP5028-19 1Left Hand Handle

CAUTIONAFor residential use only. Do not use for commercial cooking.WARNINGACARBON MONOXIDE HAZARDCombustion byproducts include carbon monoxide which

EXPLODED VIEW

TROUBLESHOOTING GUIDEIF YOU ARE EXPERIENCING DIFFICULTY AFTER FOLLOWING THIS GUIDE, PLEASE CONTACT OUR CUSTOMER SERVICE TOLL FREE - PHONE 1-800-396-38

Get it fixed, at your home or ours!Your HomeFor repair-in your home -of all major brand appliances, lawn and garden equipment, or heating and cooling

NEW OPD HANDWHEEL'External threads on Coupling Valve.Fig. 3L.P. GAS CYLINDERGas cylinders manufactured today have mechanisms to provide worry fre

2. TRANSPORTATION AND STORAGE:WARNING: Although it is safe when used properly, careless handling of the propane gas cylinder could result in fire, exp

HARDWARE#2 Phillips Screwdriver(1 piece)#8-32 X 3/8 Tapping Screw(2 pieces)1/4"-20X2" Carriage Bolt(8 pieces)#6-32 Wing Nut(Overlay)(2 piece

ASSEMBLY1. Turn leg assembly upside down as shown and insert caster plug.Make sure caster plug tab is in line with notch in leg. {SEE FIG “A”)2. Tur

5. Position left hand leg assembly as shown with console mounting tab facing up. Place non-tank side of bottom pan over bottom support. Attach bottom

7. Position side panels over legs and slide up into position. Bottom flange of side panel hooks over bottom support.